Search results

  1. b0re

    240V Fuel box with Victron ET112

    Hello, I was trying to contact victron but all the posts relating to the ET112 are closed. It's a simple setup just wanted acknowledgment of the wiring I have gone for. Victron diagram This is what I have Clearly missing the input and outputs. And also the RJ45 on pins 4,5 and 6. I...
  2. b0re

    Diesel heater (error code 7) When invertor turned on

    Its 12v. Yes, I have been using it for 6months had no issues.
  3. b0re

    Diesel heater (error code 7) When invertor turned on

    Did a test today I added an additional cable to the 12v still had the same problem. This time i turn the 12v off, then turned the inverter on then turn the 12v on im still getting the same problem. Could this be related to the Orion 24v-12v DC-DC Converters Non-isolated. I can buy an isolated...
  4. b0re

    Calculating Total Pack Ah

    Hello, I created a 7s pack each pack is 279551 milliampere-hours so 279.551Ah per pack Do you times 279.551Ah by the packs to give you the total Ah or is it 279.551Ah? Thanks
  5. b0re

    Diesel heater (error code 7) When invertor turned on

    I will swap the wire and if that does not work I will then try the capacitor option Thanks
  6. b0re

    Diesel heater (error code 7) When invertor turned on

    Hello, I have a Diesel heater powered by an Orion 24v-12v DC-DC Converters Non-isolated. When turned on everything works fine as soon as I turn on the invertor the Diesel heater shows error code 7, this means low voltage to the controller. I checked the controller's voltage when on and the...
  7. b0re

    Victron BP-65, voltage on jumper on/off

    Hello, I want to turn off the 24v via remote using Zigbee, I am currently using Sonoff. The BP-65 Victron comes with a remote loop does anyone know the voltage between the jumper on/off I want to add in a Zigbee switch between the jumper that I can tie into the rest of my Zigbee devices and...
  8. b0re

    Victron relay 12v on/off

    Can use this on a non-Victron inverter? https://www.victronenergy.com/panel-systems-remote-monitoring/phoenix-inverter-control-ve.direct Looking at the wiring it looks like you can?
  9. b0re

    Victron relay 12v on/off

    Hello, I have the Victron GX and I want to turn on and off a 12v supply its 30amp Can you recommend a relay to work with the GX? Thanks
  10. b0re

    Victron connect via bluetooth

    Ok I can connect the shunt and the mppt but can see any were in the setting to connect them to the cerbo gx
  11. b0re

    Victron connect via bluetooth

    Great will take a look
  12. b0re

    Victron connect via bluetooth

    Hello, I have a smart shunt smart solar mppt 100/30 Victron control gx cerbo gx Can I link these via Bluetooth and not use cables? Thanks
  13. b0re

    Electrical Busbar help

    This is what I have gone for the bars over the top is rated at 45amps per line. I have not cleaned up the solders or shrink-wrapped it yet. The out put cable is 400ams just because thats what i had.
  14. b0re

    how to stack your battery packs?

    Hello, I am creating a 7s 120 cell packs. I used repacker and created the 7 packs. Do I mix all the packs up or leave them with the highest to the positive connection end? Thanks
  15. b0re

    Electrical Busbar help

    The induction cooktop can pull 3200w AC, the chances of setting both hobs to 100% are very unlikely but I feed I should plan for this in case other items are running as well.
  16. b0re

    Electrical Busbar help

    The max is 3500w it will rarely see this. 99% of the time is will be only pulling 600w to 1000w. Thanks for your feedback I think I will make the bars a little thicker just because I can at this stage.
  17. b0re

    Electrical Busbar help

    I made a picture forgive me for my paint skills. If 33.4amps runs down the in rods under full loadI think I ill need something thicker for heat and efficacy reasons on all 7 packs
  18. b0re

    Electrical Busbar help

    Hello, I have created a 7s pack 120 cells per pack. The max the pack will ever seewill be 3500w thats140amps if I divide this by 7 this gives me 20amp per pack. Question - Each pack has 5 3mm copper rods going to a sold copper 3mm plate, the plate isabout an inch wide. Does the total...
Top