Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Bluetooth bms 7s connection problem
#1
II have installed Bluetooth bms of 7s , the total voltage is only 6volts when am measuring at -c . I tried it so many times . First when I spoke about this technical problem with the store on AliExpress he or she said you have removed the temp sensore wires . I thought if i connect it i will get the perfect voltage and when I tried with that the total voltage is same 6volts . I have installed as per the diagram and also by watching vdios on youtube. I did find a something am not sure of . The balance wire has a gap among them... in place of 5th pin .... when I spoke to shop person on AliExpress this is what he said 
What could be the problem??? 
By looking at the pins even the balance wire is ok whr could the problem?? Any guess


Reply
#2
Have you hooked Up b- and the other ports to the battery?
viralprankster likes this post
The Ultimate DIY Solar and build place
YouTube / Forum system setup / My webpage  Diy Tech & Repairs

Current: 10kW Mpp Hybrid | 4kW PIP4048 | 2x PCM60x | 83kWh LiFePo4 | 10kWh 14s 18650 |  66*260W Poly
Upcoming: 14S 18650~30kWh | Automatic trip breakers, and alot more
Reply
#3
daromerHave you hooked Up b- and the other ports to the battery?
At 4s connection the voltage is accordingly as shown 13.6 then when When the balance wire is been attached to the 5s pack then voltage is decreasing 
Look at the images 
Reply
#4
Are you meassuring output from bms? Did the bms shut down that port due to issues?
The Ultimate DIY Solar and build place
YouTube / Forum system setup / My webpage  Diy Tech & Repairs

Current: 10kW Mpp Hybrid | 4kW PIP4048 | 2x PCM60x | 83kWh LiFePo4 | 10kWh 14s 18650 |  66*260W Poly
Upcoming: 14S 18650~30kWh | Automatic trip breakers, and alot more
Reply
#5
Yes I am measuring from bms only. Takind -ve from bms and positive from battery . I don’t know about the shut down ... still curious to know the problem. Is it the prblm of bms ? From the manufacturer
Reply
#6
Connect the BMS up to a load and run it. Some bms systems does not enable output before you start the charge process.

Not sure about urs though but add a load on it.
The Ultimate DIY Solar and build place
YouTube / Forum system setup / My webpage  Diy Tech & Repairs

Current: 10kW Mpp Hybrid | 4kW PIP4048 | 2x PCM60x | 83kWh LiFePo4 | 10kWh 14s 18650 |  66*260W Poly
Upcoming: 14S 18650~30kWh | Automatic trip breakers, and alot more
Reply


Who read this thread?
25 User(s) read this thread:
daromer (02-12-2019, 06:39 PM), Walde (02-12-2019, 04:46 PM), Mikethezipper (02-15-2019, 03:15 AM), Beholder (02-15-2019, 12:06 AM), Leipi35 (02-15-2019, 10:44 PM), Wolf (02-12-2019, 09:59 PM), camthecam (02-13-2019, 08:01 AM), Dallski (02-12-2019, 03:17 PM), stevelectric (02-13-2019, 09:40 PM), LEDSchlucker (02-12-2019, 07:25 PM), Church1182 (02-12-2019, 09:27 PM), Cherry67 (02-14-2019, 06:08 PM), viralprankster (02-12-2019, 06:31 PM), gpn (02-12-2019, 05:44 PM), Korishan (02-12-2019, 10:15 PM), watts-on (02-13-2019, 09:44 AM), jesusangel (02-12-2019, 04:54 PM), Stefaan De Ridder (02-12-2019, 06:48 PM), Geek (02-13-2019, 03:52 AM), ChrisD5710 (02-12-2019, 01:45 PM), karmi27 (Yesterday, 09:55 PM), djuro (02-12-2019, 02:21 PM), sturgeo (02-13-2019, 12:55 PM), Issac (02-14-2019, 03:05 PM), Edster (02-13-2019, 01:31 PM)

Forum Jump:


Users browsing this thread: 1 Guest(s)