Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Grounding a pip 1648msx
#1
Testing out a PIP 1648MSX, what is the proper way to ground it? Ground, L, N are connected directly to an outlet. I plugged a power strip into the outlet and its showing no ground.

Will running the ground output from the pip to a grounding rod in earth fix that issue?
Reply
#2
I ground to both the a/c and the grounding rod. Even though the little pocket tool that has the three lights show it's properly grounded, certain equipment, like my UPS, still shows a ground fault. I never quite figure out why. Maybe there's a slight difference between earth and neutral that I'm not seeing.
Reply
#3
I don't have the same inverter, but my inverter is grounded with an 8ft grounding rod driven the whole way in. That ground is also tied to the house ground (all grounds a same potential). My testers show a proper ground.
BRAND NEW: LiFePO4 26650 Cells! Starting at $2.50 each!!
^ Use coupon code "powerwalls" on checkout for a 10% discount
Reply
#4
What kind of testers are you using? I've use these kind https://www.amazon.com/Sperry-Instrument...B000RUL2UU. They are simple circuits that light up if it's improperly grounded or wired. They test fine on mine.

I also test for voltage leakage between neutral and ground using a multimeter and I can't determine if there's any.
Reply
#5
@srk 

Hi - I have been eyeing this same MPP model.

How do you like it? What is your setup like?

Thanks
Reply
#6
Thanks for the responses. I'm seeing the same as not2bme. Ground tester checks out but belkin power strip ground light says theres an issue. I'm slightly concerned because it's only used for electronic devices and I want to ensure I have clean power.

@Solardad
I'm still in the testing phase - I've been very cautious because it's not UL listed and because ive been seeing the ground light on my power strip. I've done long term testing with small loads but now I'm starting to add more load to it and it's working well so far.

I have 6 210w panels and approximately 10kwh of 18650 cells at 48v completely off grid with separate circuits on the AC side. So far so good. I could see maxing it out relatively soon though. I'd recommend it for a hobby/small setup to learn before sinking the big bucks into a higher wattage unit. There aren't very many 48v pipes that do 120v A/C for some reason.
Reply
#7
(02-07-2019, 12:50 AM)srk Wrote: Thanks for the responses. I'm seeing the same as not2bme. Ground tester checks out but belkin power strip ground light says theres an issue. I'm slightly concerned because it's only used for electronic devices and I want to ensure I have clean power.

@Solardad
I'm still in the testing phase - I've been very cautious because it's not UL listed and because ive been seeing the ground light on my power strip. I've done long term testing with small loads but now I'm starting to add more load to it and it's working well so far.

I have 6 210w panels and approximately 10kwh of 18650 cells at 48v completely off grid with separate circuits on the AC side. So far so good. I could see maxing it out relatively soon though. I'd recommend it for a hobby/small setup to learn before sinking the big bucks into a higher wattage unit. There aren't very many 48v pipes that do 120v A/C for some reason.

Are you sure that ground light means there is an issue? Did you verify in the booklet/somewhere? I have several power strips where the ground light illuminates to let you know there IS a proper ground.
BRAND NEW: LiFePO4 26650 Cells! Starting at $2.50 each!!
^ Use coupon code "powerwalls" on checkout for a 10% discount
Reply


Who read this thread?
38 User(s) read this thread:
Sean (01-17-2019, 01:59 AM), 100fuegos (01-17-2019, 09:53 PM), ungp (02-08-2019, 08:56 PM), Sammm (02-07-2019, 02:09 AM), chuckp (02-03-2019, 07:51 PM), MGPTWEGB (02-10-2019, 10:36 PM), emuland-metroman (02-03-2019, 03:34 PM), Leipi35 (01-19-2019, 10:42 PM), Wolf (02-07-2019, 01:45 AM), camthecam (01-17-2019, 05:07 AM), Solardad (02-07-2019, 02:43 AM), RikH (01-24-2019, 09:12 PM), mart1nn (02-12-2019, 04:30 PM), LEDSchlucker (02-07-2019, 07:49 PM), Richard (01-20-2019, 04:04 PM), ma3006he (01-18-2019, 06:22 PM), beserker786 (02-07-2019, 12:03 PM), od808 (02-01-2019, 02:54 PM), Riplash (02-07-2019, 12:55 AM), Redpacket (01-21-2019, 04:36 AM), mike (02-07-2019, 02:10 AM), Korishan (02-07-2019, 02:42 AM), PAF (02-03-2019, 03:30 PM), jdeadman (02-04-2019, 04:49 AM), wim (01-21-2019, 03:34 PM), watts-on (02-07-2019, 10:16 AM), jesusangel (01-20-2019, 04:56 PM), Stefaan De Ridder (01-17-2019, 08:12 AM), Geek (02-07-2019, 02:56 AM), mr_hypno (02-07-2019, 03:31 PM), srk (02-07-2019, 11:41 AM), Chris Jardine (02-01-2019, 06:44 AM), not2bme (01-20-2019, 04:52 PM), djuro (02-07-2019, 04:51 AM), BaronVonChickenPants (01-17-2019, 09:19 AM), sturgeo (01-17-2019, 08:32 PM), Doyle (01-17-2019, 05:13 PM), Gato (02-15-2019, 11:32 PM)

Forum Jump:


Users browsing this thread: 1 Guest(s)